Skip to main content

Balance Shaft Reseal

When I started refreshing this 16v engine it was obvious to see where the oil leaks were originating - the rear of the balance shaft housings...on both sides!


As you can see from the image above - and this was after I started to clean it - the engine was caked in oily grime with fresh pools of oil behind the rear balance shaft seals. It's taken a lot of elbow grease but the engine cleaned up nice enough to begin, what I perceived to be the most arduous task - stripping off the balance shaft housings and resealing them.

With all the necessary new seals ordered up, and Loctite 574 located on eBay (as this was specified by the Porsche workshop manuals I decided to hunt some done) - it was time to tackle the flanks with vigour!

Not having any special Porsche tools meant I had to be a bit inventive with removing the balance shaft gears - they need to be locked in place while the bolt is removed.



With those out of the way then came the dreadful looking cambelt tensioner:



And finally the housings - which were then carefully cleaned. The machined surfaces need particular attention to remove all the previous Loctite residue - I took my time with this because I want to be sure that no leaks start here ever again!

Lower Balance Shaft Housing 
Upper Balance Shaft Housing
With the surfaces carefully prepared and throughly cleaned inside & out, I applied some Loctite 574 to the machined surfaces and began reassembly...


Starting with the lower balance shaft which despite it's awkward location went smoothly:


With all the bolts torqued up in correct sequence the lower balance shaft rotated freely and smoothly - it was then time to begin the upper balance shaft housing install.


This proved far more challenging for some unknown reason and I had to redo the install three times in order to get the shaft rotating smoothly. I had been very careful to keep the shafts separate so that they'd be installed into their original housing - just to be sure. When I torqued up the bolts the shaft would refuse to rotate - which after the second time was an area of concern. However, after removing the whole upper balance shaft assembly and redoing the installation for the third time - the balance shaft rotated perfectly...job done.


With the new rear balance shaft seals in place the little caps in the ends of the housing no longer move as before - and to sure up the seal even further I applied some gasket sealant along with the red rubber o-ring to fill up the gaps:


Why Porsche thought it necessary to have a floating cap inside the ends of the balance shaft housings is anyones guess - I would have thought that the fewer o-rings the better...

Comments

  1. Quad Ring parting lines are between the lobes, away from the sealing surface, thus eliminating the problems of leakage often resulting from a parting line’s irregular surface as found on an O-Ring.

    ReplyDelete
  2. done many of them ( lot of them under warranty at dealer ) fun stuff

    ReplyDelete

Post a Comment

Popular posts from this blog

Engine out the top - Easy Peasy

After reading numerous posts, the Porsche workshop manual and Clarks Garage step-by-step engine removal guide - I felt confident enough to tackle the job. But I wanted to remove the engine from the top.  As I discovered, it was pretty straight forward even for a novice! Result. I wanted to avoid removing the cross member and disturb the front suspension to do something I was convinced could be done easier from the top. Posts such as this one convinced me to give it a go at least. And I'm glad I did. In summary I was able to remove the engine from the top without needing to remove the bonnet/hood; torque tube; transaxle; bellhousing; clutch; clutch slave cylinder; cross member; front suspension; and radiator. Contrary to many so called internet experts opinions and many confusing threads this was painless and without dread. All that was necessary to remove was the starter; power steering pump and alternator (I figured to make the bottom of the engine narrower); intak

Bellhousing & Clutch fork removal

Removing the bellhousing from the Porsche 944 engine is not as complicated as it may seem - such as in this situation with my replacement engine. When I removed the original engine I detached it from the bellhousing in the car and removed the clutch pressure plate bolts through the starter motor hole - see my other post for details . In this case I decided to remove the clutch fork pivot shaft bolt. Begin by removing the four 17mm bellhousing bolts - you'll find that the bellhousing doesn't detach completely from the engine. It'll feel like its hooking on something. That something is the clutch fork pivot shaft inside the bellhousing. The bellhousing will be loose enough to rotate - turn it 180 degrees and peek through the access port which is now on top - this is what you'll see: If the engine is still in car you'll be looking at this from underneath. The pivot shaft needs to be extracted from the clutch fork. It's held in place by a small bolt on the

New Steering shaft bearing Nightmare removal

In my quest to tighten up the handling on the 944, I bought a new Needle Bearing from Porsche in an attempt to eliminate the fore-aft play in the steering at the top universal joint. The part number for the replacement is 477.419.059 and costs £88.86 posted from an OPC. Nothing like the effort required to actually remove the old one... I began the process by reading section 48 of Porsche Workshop manual. It appeared a simple enough process but two things bothered me: firstly, it required a chisel to remove a shear bolt (which in my limited experience never "shear"; and secondly a drill to remove two screws from the ignition lock. I was bothered because a quick look under the dashboard made it quite obvious that whoever had written the manual hadn't performed this task - well not without a dashboard in place that's for sure. I was bothered before I'd even started. Furthermore, the manual doesn't detail the replacement of this bearing at all - just the rem