Skip to main content

33!

Built in December 1985 in Zuffenhausen, Germany and registered in the UK on this day in January 1986. TheHoff944 is now 33!
Porsche 944 16v
This cars been in my possession for going on ten years and during that time undergone some major upgrades - including a 16v conversion, lightened & balanced flywheel and clutch, custom S2 intake, custom exhaust and adjustable SPAX poly bushed suspension now rolling on rare early offset 16” 944 Turbo Teledial alloys - amongst other upgrades.






Don’t mistake this standard looking Porsche 944 for a lethargic cruiser. It’s a whippet having had some mild lightweight treatment to compliment the increase in performance.
Porsche 944 oval dash interior
The unmarked burgundy pinstripe and half leather interior is completely original, and features the later oval dash style and an early 90’s period CD player - that honestly is hardly used due to the burbling exhaust soundtrack. 

Long live #TheHoff944
Labels:

Comments

  1. J Drew3 April 2019 at 13:50

    This comment has been removed by the author.

    ReplyDelete
    Replies
    1. 306Hoody6 May 2019 at 17:56

      This comment has been removed by the author.

      Delete
  2. 306Hoody6 May 2019 at 18:00

    This comment has been removed by the author.

    ReplyDelete
  3. disasterbus6 August 2019 at 13:34

    Lovely car, been watching your thread on Retro Rides. I've sent you a PM on there, but not sure how often you get on that forum.

    ReplyDelete

Post a Comment

Popular posts from this blog

Engine out the top - Easy Peasy

After reading numerous posts, the Porsche workshop manual and Clarks Garage step-by-step engine removal guide - I felt confident enough to tackle the job. But I wanted to remove the engine from the top.  As I discovered, it was pretty straight forward even for a novice! Result. I wanted to avoid removing the cross member and disturb the front suspension to do something I was convinced could be done easier from the top. Posts such as this one convinced me to give it a go at least. And I'm glad I did. In summary I was able to remove the engine from the top without needing to remove the bonnet/hood; torque tube; transaxle; bellhousing; clutch; clutch slave cylinder; cross member; front suspension; and radiator. Contrary to many so called internet experts opinions and many confusing threads this was painless and without dread. All that was necessary to remove was the starter; power steering pump and alternator (I figured to make the bottom of the engine narrower); intak...
19 comments
Read more

Bellhousing & Clutch fork removal

Removing the bellhousing from the Porsche 944 engine is not as complicated as it may seem - such as in this situation with my replacement engine. When I removed the original engine I detached it from the bellhousing in the car and removed the clutch pressure plate bolts through the starter motor hole - see my other post for details . In this case I decided to remove the clutch fork pivot shaft bolt. Begin by removing the four 17mm bellhousing bolts - you'll find that the bellhousing doesn't detach completely from the engine. It'll feel like its hooking on something. That something is the clutch fork pivot shaft inside the bellhousing. The bellhousing will be loose enough to rotate - turn it 180 degrees and peek through the access port which is now on top - this is what you'll see: If the engine is still in car you'll be looking at this from underneath. The pivot shaft needs to be extracted from the clutch fork. It's held in place by a small bolt on the...
5 comments
Read more

New Steering shaft bearing Nightmare removal

In my quest to tighten up the handling on the 944, I bought a new Needle Bearing from Porsche in an attempt to eliminate the fore-aft play in the steering at the top universal joint. The part number for the replacement is 477.419.059 and costs £88.86 posted from an OPC. Nothing like the effort required to actually remove the old one... I began the process by reading section 48 of Porsche Workshop manual. It appeared a simple enough process but two things bothered me: firstly, it required a chisel to remove a shear bolt (which in my limited experience never "shear"; and secondly a drill to remove two screws from the ignition lock. I was bothered because a quick look under the dashboard made it quite obvious that whoever had written the manual hadn't performed this task - well not without a dashboard in place that's for sure. I was bothered before I'd even started. Furthermore, the manual doesn't detail the replacement of this bearing at all - just the rem...
3 comments
Read more